Skip to content
HomeFAQ
Menu
← concrete masonry guides

Homeowner guide

Concrete and masonry terms homeowners should know

Plain-English concrete and masonry terms to help you read a proposal or inspection note, compare a written scope, and know when a condition needs qualified review.

Published October 2, 2026

By the HomeFAQ Editorial Team · Reviewed for accuracy.

https://homefaq.com/concrete-masonry/concrete-and-masonry-terms-homeowners-should-know/

When a proposal or inspection note uses words such as spalling, control joint, or tuckpointing, ask the professional to point out the exact area and explain what the word means for your home’s scope. These terms describe materials, parts, or conditions; they do not by themselves prove the cause of a crack, water problem, or structural concern. Use this list to compare written work, not to diagnose a slab, wall, foundation, walkway, driveway, or retaining wall yourself.

Concrete and masonry terms in plain English

Aggregate
The sand, gravel, or crushed stone mixed into concrete. It is one part of the material, not a separate layer a homeowner should expose or remove to investigate a crack.
Base
The prepared material beneath a slab, paver area, or other surface. A proposal should say whether base preparation is included and what existing soil or support conditions remain outside the stated scope.
Control joint
A planned line in a concrete slab that helps manage where shrinkage cracking is likely to occur. It can help organize cracking; it does not promise that a slab will never crack or identify why an unplanned crack appeared.
Curing
The process of protecting new concrete while it gains strength. Ask how long the area needs protection, when it can be used, and whether weather or finish requirements change that plan.
Efflorescence
A white, powdery deposit that can appear on masonry or concrete when water carries dissolved salts to the surface. It is a visible clue to discuss with a professional, not proof of the water source or a reason to seal over a moisture problem.
Expansion joint
A material-filled gap that allows adjacent building materials or sections to move differently. It is different from a control joint, so ask which joint a proposal will repair, replace, or leave in place.
Footing
The wider support at the bottom of a wall or foundation that transfers its load to the ground. Footing size and condition are not safe homeowner excavation or diagnosis questions; ask what the proposed scope actually observes or addresses.
Grading
The slope and shaping of ground around a home or project area. A concrete or masonry scope may mention grading because water movement can affect the area, but the proposal should state whether drainage work is included or needs a separate evaluation.
Mortar
The material between bricks, blocks, or stone that bonds and seals joints. It is not the same as concrete, and a masonry proposal should identify whether it is repairing joints, replacing units, or rebuilding a larger section.
Rebar
Short for reinforcing bar: steel placed inside some concrete work to help it perform as designed. Its presence, size, and placement should be stated in a written scope when relevant; do not assume it makes every slab or crack condition safe.
Repointing
Removing deteriorated mortar from the face of masonry joints and placing compatible new mortar. Repointing is different from rebuilding a wall, and it may not address movement, loose units, or water-management problems behind the visible joint.
Settlement
Downward movement of soil, a slab, or a structure. A proposal may use this word for an observed condition, but the cause and the right scope require qualified assessment rather than a conclusion from a photo or one crack.
Slab
A relatively flat piece of concrete used for surfaces such as patios, walkways, driveways, floors, or pads. A slab may have joints, reinforcement, edges, and a prepared base; ask which of those elements the scope includes.
Spalling
Flaking, chipping, or breaking away of a concrete or masonry surface. It can be a localized surface issue or part of a broader condition, so compare the proposed repair area, preparation, limits, and any concern about water or support.
Tuckpointing
A masonry repair method that uses contrasting mortar work to create the appearance of fine, finished joints. The word is sometimes used loosely in proposals; ask whether the work is decorative tuckpointing, standard repointing, or repair of damaged masonry.

Use the terms to compare a written scope

A useful proposal connects each term to an observed condition and a stated task. For a concrete surface, it may identify removal, base preparation, reinforcement, joints, finish, curing, drainage coordination, access, and cleanup. For brick, block, or stone, it may distinguish repointing from replacing units, rebuilding a section, or addressing flashing and water-management details. “Fix concrete” or “repair masonry” is too broad to compare meaningfully.

Ask the professional to mark each major item as included, excluded, an allowance, or an unknown condition. An allowance is a placeholder amount or scope, so ask what it covers and what must happen before it changes. Do not chip at a crack, dig beside a slab or wall, or try to test a leaning, loose, or shifting area. If a masonry or retaining wall is leaning, bulging, separating, or dropping material, keep people away and arrange prompt qualified local help.

Use how to compare concrete and masonry estimates to put proposals into the same checklist. If the key decision is whether a limited repair fits a documented defect or a replacement discussion is more appropriate, read Concrete repair vs. replacement. The Concrete and Masonry hub has the category’s related planning guides.

Sources

Be ready for the conversation

3 questions to ask your concrete or masonry professional

  1. 1Which terms in this proposal describe the condition you observed, and which identify work you are including or excluding?
  2. 2For the slab, wall, or masonry area at issue, what does the scope include for preparation, joints, reinforcement, mortar or finish, water management, protection, and cleanup?
  3. 3If you see movement, loose material, water, or an unknown support condition, what is within your scope to assess and when should I obtain a separate qualified evaluation?

Keep planning